Import Shared Library Report
23 марта 2020 г. 15:06:05



Your generated files are installed in the following folder:
 E:\labview-2.12.1-Labview_12.0\ximcLVx32

Parsing header file warnings:
 No errors/warnings occurred when parsing the header file.

 The following errors/warnings occurred when generating the wrapper VIs for this shared library.

VI Not Executable
 The VI is not executable because of one of the following reasons:
1. The shared library or a dependent file is not installed. To make the VI executable, you must install the shared library and all support files on the computer on which you run the VI.
2. A required custom control might be empty or cannot be found. To make the VI executable, update the custom control manually.
3. The VI contains a parameter with an unsupported data type. To make the VI executable, you must replace the empty cluster that the wizard generates with a control or indicator that uses supported data types.
    close device.vi
    command add sync in action.vi
    command add sync in action calb.vi
    command change motor.vi
    command clear fram.vi
    command eeread settings.vi
    command eesave settings.vi
    command home.vi
    command homezero.vi
    command left.vi
    command loft.vi
    command move.vi
    command move calb.vi
    command movr.vi
    command movr calb.vi
    command power off.vi
    command read robust settings.vi
    command read settings.vi
    command reset.vi
    command right.vi
    command save robust settings.vi
    command save settings.vi
    command sstp.vi
    command start measurements.vi
    command stop.vi
    command update firmware.vi
    command wait for stop.vi
    command zero.vi
    enumerate devices.vi
    free enumerate devices.vi
    get accessories settings.vi
    get analog data.vi
    get bootloader version.vi
    get brake settings.vi
    get calibration settings.vi
    get chart data.vi
    get control settings.vi
    get control settings calb.vi
    get controller name.vi
    get ctp settings.vi
    get debug read.vi
    get device count.vi
    get device information.vi
    get device name.vi
    get edges settings.vi
    get edges settings calb.vi
    get emf settings.vi
    get encoder information.vi
    get encoder settings.vi
    get engine advansed setup.vi
    get engine settings.vi
    get engine settings calb.vi
    get entype settings.vi
    get enumerate device controller name.vi
    get enumerate device information.vi
    get enumerate device serial.vi
    get enumerate device stage name.vi
    get extended settings.vi
    get extio settings.vi
    get feedback settings.vi
    get firmware version.vi
    get gear information.vi
    get gear settings.vi
    get globally unique identifier.vi
    get hallsensor information.vi
    get hallsensor settings.vi
    get home settings.vi
    get home settings calb.vi
    get init random.vi
    get joystick settings.vi
    get measurements.vi
    get motor information.vi
    get motor settings.vi
    get move settings.vi
    get move settings calb.vi
    get nonvolatile memory.vi
    get pid settings.vi
    get position.vi
    get position calb.vi
    get power settings.vi
    get secure settings.vi
    get serial number.vi
    get stage information.vi
    get stage name.vi
    get stage settings.vi
    get status.vi
    get status calb.vi
    get sync in settings.vi
    get sync in settings calb.vi
    get sync out settings.vi
    get sync out settings calb.vi
    get uart settings.vi
    goto firmware.vi
    has firmware.vi
    load correction table.vi
    msec sleep.vi
    open device.vi
    probe device.vi
    reset locks.vi
    service command updf.vi
    set accessories settings.vi
    set bindy key.vi
    set brake settings.vi
    set calibration settings.vi
    set control settings.vi
    set control settings calb.vi
    set controller name.vi
    set ctp settings.vi
    set debug write.vi
    set edges settings.vi
    set edges settings calb.vi
    set emf settings.vi
    set encoder information.vi
    set encoder settings.vi
    set engine advansed setup.vi
    set engine settings.vi
    set engine settings calb.vi
    set entype settings.vi
    set extended settings.vi
    set extio settings.vi
    set feedback settings.vi
    set gear information.vi
    set gear settings.vi
    set hallsensor information.vi
    set hallsensor settings.vi
    set home settings.vi
    set home settings calb.vi
    set joystick settings.vi
    set motor information.vi
    set motor settings.vi
    set move settings.vi
    set move settings calb.vi
    set nonvolatile memory.vi
    set pid settings.vi
    set position.vi
    set position calb.vi
    set power settings.vi
    set secure settings.vi
    set serial number.vi
    set stage information.vi
    set stage name.vi
    set stage settings.vi
    set sync in settings.vi
    set sync in settings calb.vi
    set sync out settings.vi
    set sync out settings calb.vi
    set uart settings.vi
    write key.vi
    ximc fix usbser sys.vi
    ximc version.vi